<\/div>\n\n\n\n
Five steps to get rid of sewer odours<\/h2>\n\n\n\n
The order of the steps is the method itself. If you start disinfecting straight away whilst organic contamination is still present on the surface, the odour may return.<\/p>\n\n\n\n
1. Secure the area and remove the source of the odour<\/h3>\n\n\n\n
Start by identifying the cause of the smell. It could be backflow from the drain, a leak, a blocked drain, a leaky joint, a faulty water trap, or sewage that has seeped into building materials.<\/p>\n\n\n\n
Deal with the problem before you start any chemical treatment. Remove rubbish, sludge, loose debris and any materials that are still giving off an odour. Keep people and animals away from the area until the work is complete and the surfaces have been cleaned and disinfected.<\/p>\n\n\n\n
2. Remove any sewage and wash thoroughly<\/h3>\n\n\n\n
Use a wet vacuum with a bilge pump to extract standing sewage and contaminated wash water. This makes the work safer and prevents the contamination from spreading further.<\/p>\n\n\n\n
Then clean all washable surfaces mechanically. This means that the surfaces must be scrubbed, not simply dampened with cleaning products. Use a suitable cleaning method on floors, walls, grouting, drains, skirting boards and other areas where sewage may have accumulated.<\/p>\n\n\n\n
The aim is to remove organic material before odour treatment and disinfection.<\/p>\n\n\n\n
3. Treat the odour with Biofresh<\/h3>\n\n\n\n
Once visible dirt has been removed, the surfaces are treated with Biofresh.<\/p>\n\n\n\n
Dilute Biofresh 1:10. Moisten the surface thoroughly using a low-pressure sprayer or a wet fogger. On stains, grout lines and areas with a noticeable odour, the product should be worked in with a brush.<\/p>\n\n\n\n
Leave Biofresh to work for 5 to 30 minutes. Then rinse with lukewarm water. Repeat the treatment if the odour is still noticeable after washing, drying and airing.<\/p>\n\n\n\n
4. Check before disinfecting<\/h3>\n\n\n\n
Before disinfecting, surfaces must be clean. Disinfection should not be used as a substitute for washing. Check that:<\/p>\n\n\n\n
\n- Visible contamination has been removed<\/li>\n
- No sludge, organic material or product residues remain<\/li>\n
- The surfaces have been cleaned mechanically<\/li>\n
- Surfaces and textiles that are sensitive to bleaching have been assessed prior to product selection<\/li>\n<\/ul>\n\n\n\n
This step is important. If you disinfect too early, dirt and organic matter can reduce the effectiveness of the disinfectant and cause the odour to return.<\/p>\n\n\n\n
5. Disinfect using ProffOx DES or Proff Elyte<\/h3>\n\n\n\n
Once the surfaces have been thoroughly cleaned, the treatment is completed with disinfection.<\/p>\n\n\n\n
On clean, water-resistant surfaces, apply ProffOx DES mixed in a ratio of 1:2. The product should not be rinsed off. On textiles, furnishings or surfaces sensitive to bleaching, use Proff Elyte \u2013 a ready-to-use solution with a contact time of 1 to 5 minutes.<\/p>\n\n\n\n
Choose a product based on the surface. ProffOx DES can cause discolouration and must not be used on textiles.<\/p>\n\n\n\n
<\/div>\n\n\n\n
Key rules of chemistry<\/h2>\n\n\n\n
Certain mistakes are commonly made during sewer renovation. These should be avoided:<\/p>\n\n\n\n
\n- Biofresh is not compatible with acidic cleaning products \u2013 always rinse thoroughly first if acidic products have been used<\/li>\n
- ProffOx DES can cause bleaching and must not be used on textiles<\/li>\n
- Do not mix chemicals<\/li>\n
- Disinfection should always follow thorough washing<\/li>\n<\/ul>\n\n\n\n
<\/div>\n\n\n\n
Why does the smell of sewage keep coming back?<\/h2>\n\n\n\n
Sewer odours usually return for one of three reasons.<\/p>\n\n\n\n
The first is that the source has not been stopped. If a backflow could occur again, a joint is still leaking, or a drain is missing a functioning water trap, the odour and contamination will return no matter how thoroughly you clean.<\/p>\n\n\n\n
The second reason is that organic material is left behind. It can become trapped in grouting, under skirting boards, around drains, in porous surfaces or in the drain itself. Odour treatment only works where the product can reach.<\/p>\n\n\n\n
The third reason is that people skip the mechanical wash and go straight to using a deodoriser or disinfectant. This often masks the smell for a while, but does not remove it.<\/p>\n\n\n\n
Scented products that merely mask odours do not solve the problem. Biofresh is used because it treats the source of the odour on the surface, but this requires that the area has first been cleaned and that the source has been removed.<\/p>\n\n\n\n
Always reassess the odour once the surface is completely dry and the area is well ventilated. Damp surfaces may smell less than dry ones, so a job that appears to be finished immediately after washing may still require further treatment.<\/p>\n\n\n\n
<\/div>\n\n\n\n
The products in the method<\/h2>\n\n\n\n
The method uses three chemical products, each with its own specific role: Biofresh for odour treatment of washable surfaces, ProffOx DES for disinfecting cleaned, water-resistant surfaces, and Proff Elyte where ProffOx DES may cause bleaching \u2013 for example, on textiles or more sensitive materials. In addition, a wet vacuum with a sump pump is used to remove sewage and contaminated wash water, and a low-pressure sprayer or wet fogger is used to apply Biofresh evenly.<\/p>\n\n\n\n